![]() ![]() Three sets of customizable submenu functions have been added.ġ. Fixes a phenomenon in which signal outputting of more than 100% occurs when the following combination of settings is selected.Ĩ. Support for the function that resets the clip number when the reel number is set, has been added.ħ. Please use the Canon lookup table that is released on and after November, 2018.Ħ. The HLG output is the brightness in the case of displaying on a 1000nits monitor. *2 The brightness before the change to OOTF On 83nits / OOTF Off 111nits. Ĭhanges have been made so that the and base luminance correspond to Diffuse White (100%) being 203nits*2. For LUTs that can be applied to output footage, support for the ITU-R BT.2100 standard and ITU-R BT.2408 report have been added for the following terminals: Enables AF / face detection mode to be used during Super16mm sized (2K crop) recording.ĥ. Support for these EFP lenses has been added.Ĥ. Chromatic aberration correction has been added for the following EFP lenses:ģ. Peripheral illumination / chromatic aberration correction has been added for the following lenses:Ģ. Power adapter (commercially available, DC IN 12V terminal): 4-pin XLR plug (female connector), 12 V DC (acceptable range: 11.5 V to 20 V DC), 10 A (acceptable maximum load current)ġ. Full charged V-mount battery (commercially available), 14.8 V DC (acceptable range: 12 V to 20 V DC)Ħ. An SD card reader/writer (commercially available) or an SD card slot built into the computerĥ. A 512MB or higher-capacity SD / SDHC / SDXC memory card (both commercially available)Ĥ. A computer (OS Requirements: macOS 10.7 - 10.15)ģ. A Cinema EOS C700 / EOS C700 PL camera bodyĢ. The following things are required to perform this firmware update:ġ. Before starting the firmware update operations, please be sure to carefully confirm your understanding of these instructions. The downloaded folder contains the firmware (file name: VMA8.FIM / file size: 114,524,380bytes), and instructions on the firmware update procedures (a PDF file in five languages: Japanese, English, French, Spanish and Simplified Chinese). For further information on this, please refer to the section in the unit's Instruction Manual titled "Saving and Loading Camera Settings". This saved data can be loaded into the camera and the settings can be changed after the update has been completed. It is recommended that users save their menu and custom picture settings as settings data to an SD card, separate from the one that will be used to carry out the update, before starting update operations. After the firmware update has been performed, the camera's menu and custom picture settings will be reset. Please use a commercially available SD / SDHC / SDXC memory card that is 512MB or more for the firmware update. You cannot perform the firmware update using CFast 2.0 cards. After updating the camera firmware, connect the camera with the OU-700 to update the firmware of the OU-700 from the camera's system settings. For customers who are using the optional OU-700 Remote Operation Unit, the firmware of the camera and the OU-700 Remote Operation Unit have to be the same. ![]() Once the camera is updated to the latest version, it cannot be restored to a previous version. If your camera's firmware is already version 1.0.8.1.00, it is not necessary to update the firmware. Firmware version 1.0.8.1.00 is for updating Cinema EOS C700 / EOS C700 PL cameras running firmware version 1.0.0.1.00 - 1.0.7.1.00. The following on screen display improvements have been made:įor further information, please refer to the latest version of the camera's Instruction Manual that is released with the firmware update. Added support for "Dual Pixel Focus Guide" feature.Ģ. Enable autofocus with Dual Pixel CMOS AF. Peripheral illumination / chromatic aberration correction has been added. Compatible with EF Cinema Lens CN 10 x 25 IAS S/E1. Firmware Version 1.0.8.1.00 incorporates the following fixes and enhancements:ġ. ![]()
0 Comments
Leave a Reply. |